diyobd2  27.11.2017 08:00:24

Lonsdor K518ISE OBD program VOLVO (smart) keys

What tool for VOLVO key programming? Lonsdor K518ISE only!

Lonsdor K518ISE is the first Volvo key programmer intheworldtoolto add/program new (smart)keysforallVolvomodelsviaOBD:
VolvoC30keyprogram

VolvoS40keyprogram
VolvoS60keyprogram
VolvoS80 (before2009smartkey)keyprogram;
VolvoV40keyprogram
VolvoXC60keyprogram

See how the Lonsdor K518ISE Volvo works?

Step 1: Read thesecurity data ofthe CEMmodule

Volvo's CEM are located under the co-pilot airbag on the left, remove the debris box

Read CEM data with RN-01 board:

Plug K518ISE host, adapter, and RN-01 board:

Note: the new/old CEM box looks the same, but with differentcircuits.

For theold version of the CEM box:

when openingthe lid, in the back of the circuit board, please pay attention to the black columnwith blue circles, which arethe four positioning pointsthat need to match stably with the white column of RN-01 board.

Note: The circuit board is coated with insulating glue, it is required to use the washing plate water to wash off the blue area of the insulation coating in the contact point (solder joint) , or power can not go through , if the needle of RN-01 board is broken, it will do to wire in the corresponding locations.

For thenewversion of the CEM box:

the circuit is different, which requiresto wire to read the anti-theft data

the wiring diagram

Connectpower to read the data

SeparateRN-01 board to themotherboard to prevent it from conduction

Welding cable shouldnt be more than 15cm

Step 2: Read thesecurity data of the KVM module

Volvo's KVM modules are located after the rear box, in the upside of the right rear wheel position(for 16 S60Lcar, dismantle from the right rear door to the wheel direction);

Open the module cover

Use the washing plate water to wash off the blue area of the insulation coating, or powercan not go through.

Read KVM data with FS-01board:

The positions in red circle are the 8-pin insertion points of FS-01 board:

The connection of the K518ISE machine, adapter and FS-01 board:

The most important note:

Tofailures inVolvo KVM data reading (coz the chip model is different), pleasedoas follows:

① Use programmer to read out the data (.bin file);

② Contact and send the EEPROM datato K518ISE after-sales service, theengineers will convert the data into a dedicated file;

③ ConnectK518ISE withcomputerand putthededicated file into "file ---> feature_35"folder;

④Following theoperationsto select the KVM data from the process.

Step 3: Program smart keys via OBD

Refer to the following notes:

  1. For 6 keys, duringoperation, you need to firstly insert the keyinto the key slot and then operateby following the directions.
  2. For key recognition failure, please make sure the smart keyis not locked, aslocked key cannot be programmed, the fresh new keygenerally will not be locked.
  3. K518ISE has identification& unlockfunctions, which will testand identify whether a key is an unused one or not.If the remote control is invalid after the key isprogrammed(on condition that the battery iswellinstalled and the remote control frequency is correct), try to import the CEM securitydata to unlock the keyand thenprogramagain.

Note: Only the key of this car or corresponding car can be unlockafter readingthe CEM securitydata.

4,When installingVolvo battery, please note that the two batteries are placed in an overlapway and separated by a white paper in the middle, so please do not just replace the aboveone.

Dismantlingis very simplealso , just remove the metal key, and gently pry with a not so sharp knife in the same place where the metal key lies.

Done!



:






       
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31

Blog Live
.ua